Travertine is a porous stone. Over time, its fillers fall out, the pores open up, and dirt and algae settle inside. Because it is widely used on villa terraces, pool surrounds and facades in Alanya, sun, chlorinated water and salty air speed up the wear. When honing travertine, we first fill the open pores, then grind the surface and bring it to the desired finish.
What does our travertine honing service include?
In travertine, filling is as important as honing; a floor whose voids are not sealed picks up dirt again in a short time. That is why we carry out the job as a whole: honing, filling and protection.
- Cleaning of algae, dirt and old polish residues
- Filling the opened pores with a filler matching the color of the stone
- Repair of chips and cracks
- Honing and matte finishing
- Polishing indoors, if desired
- Non-slip surface outdoors
- Water and stain protection with impregnation
- Renewal of grout joints
Areas where we perform travertine honing
Travertine is used on terraces, in gardens and around pools as much as indoors. For outdoor floors, we recommend a matte, slip-resistant finish instead of polishing.
- Pool surrounds
- Terraces and verandas
- Garden paths
- Villa living rooms
- Bathroom and shower floors
- Exterior facade cladding
- Hotel common areas
- Stairs and steps
How do we work?
- Inspection: We look at the type of stone, the condition of its pores, and whether it is indoors or outdoors, then tell you what work is needed and the price.
- Cleaning: We remove dirt, algae, and loose old filler from the pores.
- Filling: We seal the open pores with a filler matched to the tone of the stone and wait for it to dry.
- Grinding: We remove excess filler and the worn surface with diamond abrasives and level the floor.
- Finishing: Indoors we apply honing or polishing; outdoors we give the surface a non-slip texture.
- Protection and handover: We apply an impregnating sealer, clean the area, and explain how to maintain it.
Slip resistance comes first around pools and on terraces
Outdoor travertine is not polished. We leave the surface matte and lightly textured so it doesn't get slippery when wet.
- A surface that is safe to walk on barefoot around the pool
- A matte look that doesn't glare in the sun
- Impregnation protects against chlorinated water and stains
- Easy to clean because the pores are filled
If you prefer a more textured look, we can apply patinato finish.
What wears down travertine the most in Alanya?
- Chlorinated pool water: Weakens the filler and lightens the color of the stone.
- Sun and salty air: Dries out an unprotected surface and enlarges the pores.
- Algae: Settles into the pores in damp corners that stay in the shade.
- Pressure washing: Frequent pressure washing from close range strips out the filler.
That is why we recommend renewing the impregnation of outdoor travertine every few years.
State-of-the-art devices and equipment
In travertine honing work in Alanya, the first thing that determines the quality of the job on travertine floors, pool surrounds, terraces and facades is the right equipment. We choose the devices and materials according to the type of surface and the place where the work is done; we do not use products that harm human or environmental health.
- Diamond abrasives suited to the pores of travertine
- Color-matched travertine filler for filling voids
- Wet vacuum machines that instantly extract dirty water
- Final-coat equipment that provides slip resistance for outdoor areas
While working with water, we vacuum up the dirty water at the same time; the areas not being worked on can continue to be used while the job is in progress. When the job is finished, we also explain how to clean and maintain the surface day to day.
World-class quality
No matter how good the machinery and materials are, it is the craftsman's hand that produces a clean, lasting surface. Because of travertine's porous structure, if the sequence of filling, honing and polishing is not set up correctly, the holes reopen in a short time; we determine this sequence according to the stone.
For years, our team has been carrying out travertine honing work in hotels, housing complexes, villas and workplaces in all districts, especially Alanya center, Mahmutlar, Kestel, Oba, Tosmur, Cikcilli, Avsallar, Türkler, Konaklı and Okurcalar. On every job we determine the steps according to the condition of the surface, and we take the same care at every stage.
Pricing and quotes
Travertine honing is priced per square meter, and the amount of filling directly affects the price. We give you the final price after seeing the job on site; the survey is free of charge. The factors that determine the price are:
- The size of the area
- The amount of open pores and cracks
- Whether it is an indoor or outdoor space
- The desired finish: matte, satin or glossy
- Whether impregnation (sealing) is required
For preliminary information, simply send a few photos and approximate measurements via WhatsApp.
Customer satisfaction and warranty
At Alanya Mermer Silim, we carry out travertine sanding and polishing work with our own team and our own machines. Before starting, we tell you clearly what will be done, how long it will take, and how much it will cost.
- The price quoted at the inspection is the price charged when the job is done
- We work while protecting your belongings and the surrounding surfaces
- Before handing over the job, we check the result together with you
- If you notice a problem after delivery, we will come back
- Ensuring that filled gaps show no color difference and that no slippery surface is left in outdoor areas is a condition of our delivery.
Frequently asked questions
01Can travertine be polished?
02Will the filling come out again?
03Can you work while the pool is full?
04Will the color of the travertine change?
Contact us for detailed information
We come out for a site survey for travertine polishing in Alanya city center, Mahmutlar, Oba, Kestel, Konaklı, Avsallar and all surrounding towns. Service Request FormYou can fill out the phone and WhatsApp line on our contact page to reach us.
